.. _gadt: Generalised Algebraic Data Types (GADTs) ---------------------------------------- .. extension:: GADTs :shortdesc: Enable generalised algebraic data types. Implies :extension:`GADTSyntax` and :extension:`MonoLocalBinds`. :implies: :extension:`MonoLocalBinds`, :extension:`GADTSyntax` :since: 6.8.1 Allow use of Generalised Algebraic Data Types (GADTs). Generalised Algebraic Data Types generalise ordinary algebraic data types by allowing constructors to have richer return types. Here is an example: :: data Term a where Lit :: Int -> Term Int Succ :: Term Int -> Term Int IsZero :: Term Int -> Term Bool If :: Term Bool -> Term a -> Term a -> Term a Pair :: Term a -> Term b -> Term (a,b) Notice that the return type of the constructors is not always ``Term a``, as is the case with ordinary data types. This generality allows us to write a well-typed ``eval`` function for these ``Terms``: :: eval :: Term a -> a eval (Lit i) = i eval (Succ t) = 1 + eval t eval (IsZero t) = eval t == 0 eval (If b e1 e2) = if eval b then eval e1 else eval e2 eval (Pair e1 e2) = (eval e1, eval e2) The key point about GADTs is that *pattern matching causes type refinement*. For example, in the right hand side of the equation :: eval :: Term a -> a eval (Lit i) = ... the type ``a`` is refined to ``Int``. That's the whole point! A precise specification of the type rules is beyond what this user manual aspires to, but the design closely follows that described in the paper `Simple unification-based type inference for GADTs `__, (ICFP 2006). The general principle is this: *type refinement is only carried out based on user-supplied type annotations*. So if no type signature is supplied for ``eval``, no type refinement happens, and lots of obscure error messages will occur. However, the refinement is quite general. For example, if we had: :: eval :: Term a -> a -> a eval (Lit i) j = i+j the pattern match causes the type ``a`` to be refined to ``Int`` (because of the type of the constructor ``Lit``), and that refinement also applies to the type of ``j``, and the result type of the ``case`` expression. Hence the addition ``i+j`` is legal. These and many other examples are given in papers by Hongwei Xi, and Tim Sheard. There is a longer introduction `on the wiki `__, and Ralf Hinze's `Fun with phantom types `__ also has a number of examples. Note that papers may use different notation to that implemented in GHC. The rest of this section outlines the extensions to GHC that support GADTs. The extension is enabled with :extension:`GADTs`. The :extension:`GADTs` extension also sets :extension:`GADTSyntax` and :extension:`MonoLocalBinds`. - A GADT can only be declared using GADT-style syntax (:ref:`gadt-style`); the old Haskell 98 syntax for data declarations always declares an ordinary data type. The result type of each constructor must begin with the type constructor being defined, but for a GADT the arguments to the type constructor can be arbitrary monotypes. For example, in the ``Term`` data type above, the type of each constructor must end with ``Term ty``, but the ``ty`` need not be a type variable (e.g. the ``Lit`` constructor). - It is permitted to declare an ordinary algebraic data type using GADT-style syntax. What makes a GADT into a GADT is not the syntax, but rather the presence of data constructors whose result type is not just ``T a b``. - You cannot use a ``deriving`` clause for a GADT; only for an ordinary data type. - As mentioned in :ref:`gadt-style`, record syntax is supported. For example: :: data Term a where Lit :: { val :: Int } -> Term Int Succ :: { num :: Term Int } -> Term Int Pred :: { num :: Term Int } -> Term Int IsZero :: { arg :: Term Int } -> Term Bool Pair :: { arg1 :: Term a , arg2 :: Term b } -> Term (a,b) If :: { cnd :: Term Bool , tru :: Term a , fls :: Term a } -> Term a However, for GADTs there is the following additional constraint: every constructor that has a field ``f`` must have the same result type (modulo alpha conversion) Hence, in the above example, we cannot merge the ``num`` and ``arg`` fields above into a single name. Although their field types are both ``Term Int``, their selector functions actually have different types: :: num :: Term Int -> Term Int arg :: Term Bool -> Term Int See :ref:`field-selectors-and-type-applications` for a full description of how the types of top-level field selectors are determined. - When pattern-matching against data constructors drawn from a GADT, for example in a ``case`` expression, the following rules apply: - The type of the scrutinee must be rigid. - The type of the entire ``case`` expression must be rigid. - The type of any free variable mentioned in any of the ``case`` alternatives must be rigid. A type is "rigid" if it is completely known to the compiler at its binding site. The easiest way to ensure that a variable a rigid type is to give it a type signature. For more precise details see `Simple unification-based type inference for GADTs `__. The criteria implemented by GHC are given in the Appendix.